Mastering Plumbing Fundamentals for Installing a Bathtub
Mastering Plumbing Fundamentals for Installing a Bathtub
Blog Article
The article listed below in relation to Installing A Bathtub is especially compelling. Give it a try and draw your own personal conclusions.
Setting up a bath tub isn't precisely rocket science, yet it does need strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old bath tub with a new one is additionally a moderately difficult project. If the old bathtub is easily obtainable, the task can relocate easily; if you have to open up a wall surface to get rid of the old tub and place the new tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require a helper to move out the old tub and also set in the brand-new one. Ensure you have certified on your own for the job and fit attempting it. Instead of hiring a specialist to take over a halfway-completed job, it is far better to take into consideration utilizing one prior to you begin. Chances are you might need an expert plumber to make tube connections.
This post will certainly help you set up a new tub in your bathroom if you have actually currently purchased a brand-new bathtub and don't require to change the plan of your previous supply of water pipelines.
Your tools and material checklist ought to consist of the following:
Planning for the Installment
To start with, the supporting structure provided with the bath should be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid strain on the bathtub.
Fit the adaptable faucet adapters to the bottom of the two taps utilizing 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet with the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you use all of the provided washers.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be suited its final position.
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, then the first thing you need to do is detach the supply of water. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of eliminating the existing taps can be rather troublesome as a result of the restricted accessibility that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the faucets. Have a towel all set for the staying water that will certainly originate from the pipes. As soon as the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from transforming during this process. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any old securing compound.
Prior to proceeding to fit the new taps, contrast the pipe connections on the old taps to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Mounting the Bath tub
Utilizing the two wooden boards under its feet, position the tub in the required placement. The wooden boards are practical in uniformly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four tiny factors.
The following goal is to ensure that the bath tub is leveled all round. This can be attained by examining the spirit level as well as readjusting the feet on the tub till the spirit level reads level.
To mount faucets, fit all-time low of the outermost flexible faucet port to the ideal supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Switch on the water system and examine all joints and also brand-new pipework for leaks and tighten them if necessary. Load the tub and additionally inspect the overflow outlet as well as the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as described in the producer's user's manual. Tiling as well as sealing around the bathtub must wait till the bathtub has been made use of at the very least once as this will resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to avoid damages to the thread. One end of the port fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will call for reducing couplers, which links the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the faucet in the mounting opening in the bath/basin ensuring that the washers are in place between the faucet as well as the sink. Secure the tap in position with the maker offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap ports. The former kind should be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the area where the bath meets the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, triggering the water to permeate the wall surface in between the bath as well as the tiling, causing difficulties with moisture as well as feasible leakages to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your components and installations. They are sold in tubes and also cartridges, as well as can sealing gaps as much as a width of 3mm (1/8 inch). If you have a larger space to load, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly fill up the bathtub with water before securing, to allow for the activity experienced when the tub remains in use. The sealer can split rather very early if you do not take into consideration this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally quickly readily available on the marketplace. It is advisable to fit the ceramic tiles using waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious person who reads on Installing A Bathtub, I assumed sharing that piece of writing was a great idea. Loved our blog? Please share it. Let someone else check it out. Thanks a lot for your time. Don't forget to check our site back soon.
Click Here To Read More Report this page